How to Install WPC Decking and Wall Cladding

How to install WPC decking and wall cladding: frame, matched clip set, gaps, end trims and fence posts. Confirm the clip list before ordering in bulk. Quote within 24 hours.

WPC decking fixes to a levelled frame with concealed clips, so no screw breaks the surface; wall cladding is screwed at the panel joints, hidden by the next panel. This guide covers what decides whether a deck stays flat — the frame, the right clip set, the gap between boards, and how to close the ends — and what to confirm before ordering.

What does a WPC deck fix to?

A levelled supporting frame. Boards fix to joists with concealed clips, and the clips and screws are matched to each board and joist section — they can be supplied as a set, with OEM packing and mixed loading available. Fix the joists to the base first, with expansion anchors (nylon plug + screw): drill through the joist into the concrete, tap in the plug, drive the screw down. No board goes on until the joists are fixed and level. Where the ground or the base needs it, a joist support system goes under the frame: U-clips for lateral take-off and cross joints where tubes cross, sized and combined to the substrate and the project. Frame centres are 300–400 mm, following the board profile, the span and the expected load; confirm the exact centres for your board before ordering.

Which clip goes with which board?

The clip follows the board. The range covers a starter clip for the first edge, a decking clip for the run of boards, a wing clip, and the matching screws — countersunk, self-drilling and fine-thread, in standard and black finishes. Clips and screws are matched to each board and joist section and can be supplied as a set, so one order covers the boards and their fixings together. Different boards need their matching clip, so confirm the matching list before ordering in bulk. Plastic fixings — square clips, U-clips and anchors with screws — are selected by installation method and substrate, and can ship together with the clips and screws.

How much gap do boards leave?

Leave a 5 mm gap between boards. The groove takes the concealed clip, and the clip sets the joint — so the gap is decided by the clip and the board, not by eye. For ASA boards the catalogue gives 2–3 mm with the standard clip and 6–7 mm only where drainage is wanted; WPC boards are quoted per order, so confirm the gap for your board before the crew starts.

Why do boards need gaps?

WPC boards expand and contract with temperature. It is a natural characteristic of the material — it cannot be stopped, only reduced. That is what the gaps are for: a 5 mm gap between boards gives the movement somewhere to go. The movement is more noticeable in spring and autumn, when the temperature swings between night and day, and it settles in summer. Do not butt boards tight — a deck fixed tight in cool weather will buckle when it warms up.

How do you finish the ends and the fence?

Close every cut. Edge trims cover the board ends so no cut core stays visible. Fix the trims with screws driven directly through the trim face — decking and cladding trims fix the same way. The same logic runs through the accessories: fascia and end trims close the perimeter. For fencing, the method is different — set the posts first. Posts run 2,400 mm including the buried section: dig the hole, set the post, check vertical with a level, then grout it in. Do not fit the slats and boards until the grout has cured. Fence fittings come in two methods with six items, matched to the fence boards.

What should you confirm before ordering?

Four things. First, the model, the colour and the quantity — send them and we reply with a quote within 24 hours. Second, the matching list: which clip set, which joist section and which support parts go with your boards. Third, the base: tell us the substrate and the span so the frame and the supports are sized to the project. Fourth, the sample: confirm the colour and finish on a free physical sample before ordering in bulk, because screen colours are not a reliable match.

Frequently asked questions

Do WPC decking boards need screws through the face? No. Decking fixes with concealed clips in the groove, so the fixing does not go through the face. Wall cladding is different: it is screwed through the tongue at the joint, and the next panel covers the screw heads. Will the boards expand and contract? Yes — it is natural for WPC and cannot be stopped, only reduced. The 5 mm gaps absorb the movement. It shows most in spring and autumn, when nights are cold and days are warm, and settles in summer. Which clip set do I need? The set matched to your board and joist section — starter clip, decking clip or wing clip, with the matching screws. Confirm the matching list before ordering in bulk. What holds the frame up? A joist support system under the frame: U-clips and cross joints, combined to the substrate and the project. How do you install a WPC fence? Set 2,400 mm posts first — dig, level, grout — and fit the slats only after the grout has cured. How do you finish the cut ends? Close them with the matching edge trim, so no cut core stays visible. How do I get a quote? Send the model, colour and quantity to eva@thomestyle.com (WhatsApp / WeChat +86 15956288470) and we will reply within 24 hours.

Read next

More from T*Home

Installation guides and material notes for WPC decking, wall cladding and fencing.