Download
T Home WPC Fencing Installation Guide
Step-by-step guide to installing T Home WPC fencing: base mounting on hard ground or in-ground concrete footings. Posts at 1800 mm centres, 3–5 mm board gaps.
This guide covers the installation of T Home WPC fencing: boards, posts, rails and fittings, in the two methods the system is made for — base mounting on finished hard ground, and in-ground with concrete footings. Read it in full before the first post goes in. Posts, rails, boards and fittings ship as one kit; use the parts matched to your boards, and confirm the layout — post centres, corners and any gate — before you dig or drill.
1 System covered
- Fence boards: 157–210 mm wide, about 20 mm thick; first-generation and capped (co-extruded) boards in the same 10-colour and 8-colour cards as the decking range
- Posts: 70 × 70, 80 × 80 or 100 × 100 mm; 1950 mm for base mounting, 2400 mm for in-ground
- Post bases: Two designs, fixed with expansion bolts
- Post caps: Aluminium or plastic, square or pointed
- Upper / lower rails: Same profile, or male-female interlock
- L-brackets: Steel or aluminium, for corners and ends
- Decorative panels: Aluminium or PVC, pattern customised on request
The system suits residential gardens, villa perimeters, commercial courtyards, pool enclosures and landscape partitions. Other sizes and sections are customised on request.
2 Tools and materials
- Tape measure; spirit level (600 mm or longer); string line and pegs: T Home fence boards, posts, rails and fittings
- Spade or post-hole digger; wheelbarrow and mixing tub: Concrete mix (grade C20 or above) and gravel for in-ground posts
- Impact drill; drill bits to suit the expansion anchors (usually 12 or 14 mm): Expansion anchor bolts for base mounting
- Circular saw or mitre saw with a fine-tooth blade: Post caps; L-brackets; decorative panels where specified
- Rubber mallet; 3–5 mm spacers: Bracing timber and pegs
- Pencil and marker: Topsoil or sand to finish around footings
Posts, rails, boards and fittings ship as one kit. Check the model, colour and quantity on delivery and report any damage before installation starts.
3 Storage, handling and safety
- Store boards and posts flat on a level surface, off wet ground and out of direct sunlight.
- Carry boards on edge or with two people. Do not drag them across rough ground.
- Check for buried cables, pipes and drains before you dig. Call the local utility marking service where one exists.
- Wear gloves and eye protection. Mix concrete in a well-ventilated area and wash splashes off skin at once.
- Do not burn off-cuts. Keep children away from the work area — and from open post holes — until the job is finished.
4 Planning the run
- Mark the boundary and check it against the property line and any local planning rules or height limits before you build.
- Run a string line along the fence and mark every post centre at 1800 mm. Measure twice: boards are cut to the post spacing, and a post out of place cannot be moved once the concrete sets.
- Set the end and corner posts first. They fix the line; every post between them follows.
- On a slope, step the panels: keep each bay level and drop the next bay down, rather than running boards on a slant.
- Confirm where gates go before you set posts. Gate posts carry the hinges and the weight of the gate — allow for heavier fixings there.
- Post height, buried depth and centres in this guide are standard practice. Adjust them to panel height, wind load and ground conditions; in exposed or high-wind sites, shorten the centres.
5 Method A — Base mounting
For finished concrete or stone ground, where no digging is wanted. Uses the 1950 mm post on a bolted base.
- Drill the ground: mark the fixing points through the base plate and drill holes to suit the expansion anchors, usually 12 or 14 mm across and 80–100 mm deep. Clean the dust out of every hole.
- Fix the base: set the base plate on the mark and tighten it down with expansion bolts.
- Fix the post: seat the post on the base plate and lock it with the horizontal bolts.
- Put the rails in: seat the lower rail in the post grooves, slide the boards in one at a time, then press the upper rail on.
Confirm the post's corner direction and the groove orientation before you fix the base — a base bolted down facing the wrong way has to come off again.
6 Method B — In-ground installation
For soil, lawn and unfinished ground. Uses the 2400 mm post, with 500 mm buried and 1800 mm standing above ground.
- Mark the post centres at 1800 mm along the string line.
- Dig each hole about 300 mm across and 600 mm deep. Put 150 mm of gravel in the bottom of the hole so water drains away from the post.
- Set the post in the hole so 500 mm is buried and 1800 mm stands above ground. Check plumb in both directions with a spirit level — 90° to the ground — and brace the post with timber so it cannot move.
- Pour concrete around the post, up to about 50 mm below ground level. Tap the post gently with a rubber mallet to work out air pockets.
- Let the concrete cure fully — usually 24–48 hours — before fitting rails and boards. In cold or damp weather allow longer. Do not load a post before it has cured.
- Finish the top of the footing with topsoil or sand to ground level.
7 Fitting rails and boards
- Seat the lower rail in the grooves of two set posts.
- Slide the boards in one at a time from the top, keeping each board level.
- Leave a 3–5 mm gap between the end of each board and the inside of the post, so the boards can expand in summer heat. Use spacers to keep the gaps even.
- Keep at least a 30 mm gap under the lowest board, so water drains and the board never sits in wet soil.
- Press the upper rail on last, then fit the post caps.
- Check plumb and level as you finish each bay — a bay that leans will show in the next one.
Never bury the bottom of a fence board in the ground. Boards that sit in soil stay wet, and a fence fixed tight in cool weather will buckle when it warms up.
8 Corners, ends and decorative panels
- Corners and end posts take L-brackets — steel or aluminium — fixed to the post and the rail ends.
- Close every post with a cap: aluminium or plastic, square or pointed to match the run.
- Decorative panels (aluminium or PVC, pattern customised on request) fit in place of boards in the same rails.
- Where a fence meets a wall, fix the end post with brackets and leave the same 3–5 mm expansion gap between the last board and the wall.
9 Inspection checklist
- Line: Posts straight along the string line; bays level, stepped neatly on slopes.
- Plumb: Every post at 90° in both directions.
- Centres: 1800 mm between post centres; boards fit without forcing.
- Gaps: 3–5 mm at board ends; at least 30 mm under the lowest board.
- Footings: Concrete cured before rails went on; tops finished to ground level.
- Finishing: Caps on every post; rails seated; brackets tight at corners and ends.
- Site: Holes backfilled; off-cuts removed.
Care: wash the fence with clean water and a soft brush. Do not use abrasive cleaners on the capped faces.
Questions or a quote for your next order: eva@thomestyle.com · WhatsApp / WeChat +86 15956288470 · www.thomestyle.com — send the model, colour and quantity; we reply with a quote within 24 hours.
